preload preload preload preload

The angle is exposed to the real-time failure diagnostic system of the ball bearing


31st August 2013 Bearing Technology 0 Comments
Horn exposed to the intersection of ball bearing and the intersection of real-time failure and diagnostic system include the intersection of hardware and part and the intersection of software and part mainly 1 The part of the hardware: Mainly use and imitate resonance demodulation technique of the circuit implementation [3-4 ] and digital signal processing circuit design. The intersection of impact and signal that trouble produce bring about resonance in hardware resonator, modulate to the resonance signal to reach high frequency faint the intersection of impact and signal through sympathetic ...
Read More »

The angle contacts the high-speed rotation attentive matters of the ball bearing


31st August 2013 Bearing Technology 0 Comments
The attentive matters of high-speed rotation: The angle contacts the ball bearing when the high-speed rotation, especially rotational speed is close to or exceed the terminal rotational speed that the size table records, should pay attention to the following item mainly: 1 Use the accurate angle to contact the ball bearing 2 It is analyzed that the horn is exposed to the backlash inside the ball bearing ' Consider the angle that temperature rise produces is exposed to the backlash reduction within the ball bearing 3 Analyze the pattern of the material of the retainer to ...
Read More »

The angle contacts the ball bearing and installs and uses three major attentive matters


31st August 2013 Bearing Technology 0 Comments
The angle contacts the ball bearing and installs and uses three major attentive matters 1.The setting angle should be forced evenly while keeping in touch the ball bearing, can't hammer directly. For instance: Having cooperated and is full of bigger, the ball bearing is placed on automatically should contact the angle ing Accuse of heating in the thermal air heating furnace or oil furnace, the heating temperature is controlled below 100 degrees strictly. 2.Serial stable operation for a long time under - 40 degrees - 120 degrees that the angle equipped with nylon retainer can exposed to the ...
Read More »

The angle is exposed to the preloading concrete method of the ball bearing


30th August 2013 Bearing Technology 0 Comments
When corner keeps in touch the ball bearing and positions the quantity of lying in preloading compared with preloading of level pressure of preloading and is equal to, position preloading to be relatively large to the intersection of bearing and rigid result of increase, change impact on bearing load to be too light much rigidly position preloading. Position preloading in use, the axial difference in the lengths caused by temperature difference of axle and pedestal, radial expansion and influence that moves etc. caused by load that the temperature difference of the Internal and external cycle ...
Read More »

The angle is exposed to the determination of the running speed of the ball bearing


30th August 2013 Bearing Technology 0 Comments
While producing, the antifriction bearing has a limit at the speed of runtime. This limit speed is contacted the material of the part of the ball bearing to presume by the operating temperature or angle of lubricant. There is open horn in the regular backlash that contacts the ball bearing and uses for the grease lubrication horn and contacts the ball bearing: Lubricant: Contain the regular lithium soap grease lubrication of mineral group oil, the degree of viscosity in 40 degrees Centigrade is from 100 to 200mm2/s such as ISO VG 150 The angle contacts the ball bearing reference burning ...
Read More »

How to improve the angle and is exposed to the ball bearing precision


30th August 2013 Bearing Technology 0 Comments
How to improve the angle and is exposed to the ball bearing precision: 1,The basic shaft is exposed to the ball bearing with the angle but its precision still can't meet the demands, and then add the thick journal and make ball track on it in order to replace the inner circle, and it needs dense measurement to carry on the steel ball, by a series of of every three of size, each group of steel balls is fetched and close to 120 degrees of intervals to separate, because of reducing by one and processing the surface again, has reduced by one and cooperated with the surface again, improve axle ...
Read More »

The angle is exposed to the ball bearing and install way installation, angle and contact the ball bearing correctly


30th August 2013 Bearing Technology 0 Comments
1,Use brute force when the installation, beat horn, exposed to the intersection of ball bearing and opposite angle, keep in touch the ball bearing, injure maximum directly with hammer; Cause the major cause out of shape. 2,Installation is uncomplete, install the deflection or not put into the angle and contact the location of ball bearing, it is too small to cause the angle to be exposed to the backlash of ball bearing. The Internal and external cycle is not at the same center of rotation, cause different hearts. Propose: Choose the appropriate or specialized angle to contact the installation ...
Read More »

The angle contacts the high-speed rotation attentive matters of the ball bearing


30th August 2013 Bearing Technology 0 Comments
The attentive matters of high-speed rotation: The angle contacts the ball bearing when the high-speed rotation, especially rotational speed is close to or exceed the terminal rotational speed that the size table records, should pay attention to the following item mainly: 1 Use the accurate angle to contact the ball bearing 2 It is analyzed that the horn is exposed to the backlash inside the ball bearing ' Consider the angle that temperature rise produces is exposed to the backlash reduction within the ball bearing 3 Analyze the pattern of the material of the retainer to ...
Read More »

The angle contacts the hermetic characteristic of the ball bearing


30th August 2013 Bearing Technology 0 Comments
It is sealed that ball bearing support placement that the angle contacts is non-contact type: 1.The interval is sealed: Simple in construction, can meet the sealed requirement under the general condition. The choice d of the interval e is less than or equal to 50mm, e =0.25- 0.40mm; d> 50mm, e =0.25- 0.6mm. 2.The ditch groove is sealed: Pack the grease in the ditch groove, make the dust difficult to invade, there are recess and helical groove two kinds of forms. The recess generally has 3. Groove width b =3- 5mm; Groove depth t =4- 5mm. 3.Labyrinth packing: After the curved path of the ...
Read More »

The miniature angle contacts the processing course of the ball bearing major part


30th August 2013 Bearing Technology 0 Comments
The miniature angle contacts the processing course of the ball bearing major part: 1. The processing course of the collar: Miniature horn exposed to ball bearing the intersection of cycle sum and processing of outer lane it depends on raw materials or blanks to be formal and different and different to some extent, among them the process before processing of car can be divided into the following three kinds, the whole processing course is: The bar or tube is expected ' Some are excellent The material needs forging and annealing, normalizing ----The car is processed ----Heat treatment ...
Read More »