preload preload preload preload

IKO imports the bearing and uses the method lengthened life cycle


28th February 2013 Bearing Technology 0 Comments
For can make the intersection of IKO and imported life time of bearing long, we share IKO import the bearing use the method lengthened life cycle together with everybody today, it be able to be helpful to everybody to hope. 1,IKO imports the installation of the bearing Whether the installation that IKO imports the bearing is correct, influence the precision, life-span, characteristic. So, design and assembly department as to the thing that abundant research in the installation of the bearing yes. The hope should be installed according to the operation or work standard. The canonial project of ...
Read More »

Judge the exactness installed in use of IKO bearing


28th February 2013 Bearing Technology 0 Comments
IKO bearing is a composite member which supports axial rotation. The rolling element of its set of cycle sums undergoes precision finishing. The bearing, before being dispatched from the factory, for not protecting the ball track and surface of rolling element the corrosion, have poured into the rust-preventive oil or antirust grease between ball track and rolling element. So the bearing should be washed before installation. The bearing sealed up for safekeeping with the rust-preventive oil can be washed directly with the petrol or kerosene; Use thick oil or antirust oil to be anti-corrosive, ...
Read More »

Damage and countermeasure of INA bearing


28th February 2013 Bearing Technology 0 Comments
INA bearing under accurate use, there can be very long life-span. If the premature appearance is damaged, probably because the lectotype will be wrong, will improperly use, or it is bad to lubricate to cause. So, while installing INA bearing, we need to record the machine kind, install the placement, service conditions and cooperating around, through studying the type of summarizing INA bearing and damaging, the environment for use when the problem takes place, in order to prevent the situation from recuring. The unable direct observation INA bearing while operating, but through the noise, ...
Read More »

The ball-and-socket bearing two-way thrust ball bearing contrasts with ball bearing characteristic of major groove


28th February 2013 Bearing Technology 0 Comments
The two-way thrust ball bearing of the ball-and-socket bearing contrasts with ball bearing characteristic of major groove: The ball-and-socket bearing is a kind of special structural sliding bearing. Its structure is simpler than the antifriction bearing, it is mainly made up by an inner cycle sum with exterior sphere and an outer lane with inner sphere, can bear greater load, type and structure on the basis of the it, can bear radial load, axial load or union load coexisting radially, axially. Two-way thrust ball bearing, can bear two-way axial load. Two-way thrust ball bearing, among them ...
Read More »

How does this pays and stores IKO bearing


28th February 2013 Bearing Technology 0 Comments
IKO bearing is a kind of delicate mechanical component, preserve and keep comparatively rigorous requirement for it, must control and store temperature and relative humidity of the room. Prevent the too loud temperature from change ' But the seasonal temperature change does not quite influence Should store the room: Clean and dry Prevent the air flow If the relative humidity of storing the room is greater than 75%, propose allocating the air conditioner Prevent shaking Keep the constancy of temperature ' The temperature of 48 hours does not change much at 3 ℃ Bearing coat with ...
Read More »

Breakdown maintenance method of generating heat of IKO bearing


28th February 2013 Bearing Technology 0 Comments
The bearing is fixed parts in the machinery, it is the mechanical body, its function is basically the central position used for keeping the axle, and control this kinematic parts. IKO bearing has very important function in any machinery, if there is no bearing, machinery can't operate. A lot of users reflect, when using IKO bearing, the trouble that the bearing generates heat is the most common, this trouble will also influence life-span and characteristic of the bearing. Then, how formative is this kind of trouble? Below, some knowledge summed up for everybody. 1,The oil level is too low, ...
Read More »

SKF bearing premature aging reason diagnostic method


28th February 2013 Bearing Technology 0 Comments
For the characteristic of making SKF bearing rolling have, can maintain long term administration under the good condition, must maintain check sum to the bearing, this kind checks and maintains bearing and keeps and sees the bearing of the adjoining page store before putting ,It is very important to advancing trouble-savingly, hope to operate the operating standard of the condition according to the suitable machine, maintain fixed check sum, generally adopt the following method: Get in the quantity checking, rolling, vibration, the intersection of check sum and property of lubricant of ...
Read More »

Association constructional design of IKO bearing


28th February 2013 Bearing Technology 1 Comment
It is machine component of quantity production to roll IKO bearing, and it is very tight to make accuracy requirement, the specialization intensity is very high technically, so for IKO bearing variety apt to buy of the overwhelming majority, should buy more worthwhily than to repair, only consider the repair question of IKO bearing in case of the following, namely: 1A large number of IKO bearings of the same type which the large-scale factory uses, its failure mode, mainly in order to roll the external abrasion, fatigue or inch abrasion, especially it is mostly retainers or rolling elements ...
Read More »

Roller bearing cente adjusting ball bearing and other spherical bearing characteristic contrast of cente adjusting


28th February 2013 Bearing Technology 0 Comments
Roller bearing cente adjusting ball bearing and other spherical bearing characteristic of cente adjusting are compared with: The ball bearing outer lane ball track of cente adjusting is the spherical shape, so have cente adjusting characteristics, as the axle is forced bends or slopes and makes the mean line of inner circle opposite to mean line of outer lane and slope and does not exceed 1 ...
Read More »

Winter maintain uniline’s corner joint of roller bearing of circular cone of ball bearing of major groove of the bearing


28th February 2013 Bearing Technology 0 Comments
Winter maintain the ball bearing taper roller bearing uniline angle of major groove of bearing and is exposed to the ball bearing knowledge: Major groove the intersection of ball bearing and the bearing have certain the intersection of cente adjusting and ability also, as 2 ' when the 10 ' of inclined relative to exterior shell holing, can still work normally, but there is a certain influence on bearing life-span. Ball bearing retainers of major groove are mostly that the steel plates ram the wave shape retainer, the large-scale bearing adopt the car to make metal entity retainer more. Winter ...
Read More »