preload preload preload preload

Case study of nine kinds of common troubles of bearing


31st May 2011 Bearing Technology 0 Comments
Bearing nine kind common case study of trouble ' 9 kinds of common causes that dissuade from of bearing : It is a common occurrence that the bearing is operating and presenting dissuading in the course from, so needn't be surprised at. Having dissuaded from, it is links to be dogmatic and handle. We explain a common cause that dissuade from of FAG bearing on a day. 1,The bearing is too high in temperature: While operating in the organization, install the placement of the bearing and answer a temperature made, when stroking the outer cover of organization by hand, should regard feeling and ...
Read More »

Maintain the water pump bearing method


31st May 2011 Bearing Technology 0 Comments
Maintain the water pump bearing method: 1,The water pump coming into operation newly, generally must change the grease oil after operating 100 hours ,Run and change once every 500 hours each time later. 2,Adopt the floating bearing that the grease lubricates, after running for 1500 hours, should change the grease, there can't be too much or too little oil content with note, because there is too muchly or too little grease will cause the bearing to generate heat, the fuel quantity is generally known in 1/2- 2/3 of the volume of bearing room. 3,For adopting and lubricating the bearing of the ...
Read More »

SKF angle is exposed to the ball bearing to design – seal the bearing introduction


31st May 2011 Bearing Technology 0 Comments
SKF imported bearing angle contacts the ball bearing and designs - seal the bearing: It can also be with sealing that the high-accuracy angle of the most common SKF contacts the ball bearing. These bearings are installed and sealed with low friction, form one and extremely narrow disparity of cylinder surface of endocyclic shoulder, it is nearly contactless both sides. The paper strip seal is by a piece of petroleum and wear-resisting nitrile rubber NBR ,And strengthen with the steel plate. The operating temperature range of these seals is - 25 ...
Read More »

The angle contacts the design of the ball bearing – mix the bearing


31st May 2011 Bearing Technology 0 Comments
SKF bearing angle contacts the design of the ball bearing - mix the bearing The most common high-accuracy angle of SKF bearing contacts the same standard configuration of the ball bearing: -All steel bearing -Ceramic ' Silicon nitride The balls mix the bearing Because the silicon nitride ball is lighter than the steel, the balls are quite difficult, mix the bearing stiffness and running speed that can offer the higher intensity are much higher than the constant all steel bearing. Low centrifugal force of heat that bearing and bearing are being produced of losing weight of ceramic ball ...
Read More »

SKF angle contacts the appearance design of the ball bearing


31st May 2011 Bearing Technology 0 Comments
SKF imported bearing angle contacts the appearance design of the ball bearing SKF imports the bearing series: The high-accuracy angle is exposed to ball bearing SKF range and include three serial bearings: -Those of series 719 are extremely light -Those of series 70 are smooth -Powerful series 72 Horizontal stroke three bearing here ...
Read More »

The angle is contacted the ball bearing is introduced – SKF imports the bearing


31st May 2011 Bearing Technology 0 Comments
The angle is contacted the ball bearing is introduced - SKF imports the bearing: The high-accuracy angle that SKF offers is exposed to great choice of the ball bearing - type and quantity not merely for designing, and size quantity. It includes the axle diameter from 8 to 320 millimetres, including application and other arrangements of the precision mainshaft of almost all the lathes can be used to contact the ball bearing on the high-accuracy angle. It is indecomposable since horn exposed to by ball bearing with - horns like all exposed to by ball bearing - to drift about aimlessly each ...
Read More »

SKF naming system and SNFA naming system diagram of the bearing


31st May 2011 Bearing Technology 0 Comments
SKF naming system and SNFA naming system diagram of the bearing: The following is that S K F angle is exposed to the guide screw naming system of the thrust ball bearing. Appointed to mark the outer surface to the bearing of bearing. Exposed to the intersection of thrust ball bearing and the intersection of guide screw and table that offer under naming system the following definitions to the intersection of SKF-SNFA and ultraprecise horn: -The naming system of SKF: -SNFA naming system: Chinese car bearing network editor. ...
Read More »

Ultimate standard of bearing strength of needle roller of thrust


31st May 2011 Bearing Technology 0 Comments
Technological digest: The breakdown point of the thrust needle bearing depends on the kind of thickening agent and consumption in the thrust needle bearing to a great extent, the soap content increases, then breakdown point increases too. Also temperature-dependent. The higher the temperature is, then the smaller the breakdown point of the lipoprotein is; Drop in temperature, then the breakdown point of the lipoprotein increases. Determine the ultimate strength standard method of needle bearing of thrust is SH/T 0323-92, determine the maximum pressure when displacement takes place that the ...
Read More »

Shortcomings of the antifriction bearing all have those


31st May 2011 Bearing Technology 0 Comments
1. The ability that the antifriction bearing bears load is much smaller than the sliding bearing of the same volume, so, antifriction bearing is radial and roomy. So bear occasion of heave- load and require radial size little, structure require compact the intersection of occasion and <the intersection of internal-combustion engine and the intersection of crankshaft and bearing ,Adopt more sliding bearings; 2. Vibration and noise of antifriction bearing are relatively great, especially inuse is particularly prominent on later stage, so, have very high expectations for precision, there ...
Read More »

Advantage comparative analysis of the antifriction bearing


31st May 2011 Bearing Technology 0 Comments
1. The coefficient of friction of the antifriction bearing is smaller than the sliding bearing, transmit high efficiency. The coefficient of friction of the general sliding bearing is 0.08-0.12, and the coefficient of friction of the antifriction bearing is only 0.001-0.005; 2. The antifriction bearing has already realized canonicalization, seriation, generalization, is suitable for producing in enormous quantities and supplying, it is very convenient to use and maintain; 3. The antifriction bearing is made of bearing steel, and pass the heat treatment, so, the antifriction bearing not ...
Read More »