preload preload preload preload

What quality of seeing a bearing you are to teach


26th February 2009 Bearing Technology 0 Comments
1 see to use material bearing steel at first, Germany FAG whether one's own specialized steel mill produce, come out in bearing, higher than the fake FAG bearing in hardness and at being accurate. 2 adopt the intersection of high investment and the intersection of mark and apparatus, for establish the intersection of enterprise and brand image, prevent products from counterfeit, FAG bearing producer adopts the laser mark machine, hopes to be establishing the corporate image, in line with international standards, control products with high investment counterfeit, but, because the laser mark ...
Read More »

Inlay the solid from the lubricated bearing FZF-4 in steel base


26th February 2009 Bearing Technology 1 Comment
Inlay the solid from the lubricated bearing FZF-4 in steel base Product structure FZF-4 steel base regards tool steel of alloy as the matrice to inlays the solid lubricated bearing, solid lubricant inlaying the special prescription according to certain angle and density on the surface is made, this product has higher resisting and pressing performance, in the course of using, make solid lubricant and axle rub through the frictional heat, form the compatible excellent condition that lubricates of the oil, powder, has already protected axle from abrading, make solid lubricant characteristic ...
Read More »

Powder metallurgy is from the lubricated bearing material standard


26th February 2009 Bearing Technology 0 Comments
Powder metallurgy can be hardened from the lubricated bearing material standard with the heat treatment. This kind of material has high wearability and high compression strength. In order to lighten the material expenses, the bronze can use 40%- 60% the quality mark The iron dilutes. In order that lubricating, these bearings usually all contain 05%- 13% the quality mark Graphite. The bearing should frit and have minimums to carbon content of compound. This kind bearing is light to load medium-sizedly without being used ined with under terms at a high speeds medium-sized. Often substitute and ...
Read More »

Reason and suggestion causing the bearing to be damaged in early days


26th February 2009 Bearing Technology 1 Comment
Lead to the fact various possible reasons damaged early period of bearing and propose correspondingly: 1st, installation is improper account for 16% 1 , use rough strength when the installation, it beats bearings to be most loud to the intersection of bearing and injury directly with hammer; Cause the main reason out of shape. 2 , install uncompletely, installation have offset or put the intersection of bearing and location into, cause the intersection of bearing and backlash too little. Inside and outside if you can't enclose, the same centre of gyration when ating,last heart. ...
Read More »

” structural membrane of ball bearing of nanometer ” It is healthy to protect the car effectively


23rd February 2009 Bearing Technology 0 Comments
" Abrade " It is a killer who endangers the car health. The statistics show, 80% of the car troubles come from car inside's maintaining insufficiently, causes the engine to excessively abrade, the power decline appears, the oil consumption is raised, the engine noise is loud, the bike is shaken, burn the engine oil etc., influence the going normally of the vehicle. Scheme that and nanometer lubricating oil additive researched and developed by Professor Li ZhengXiao, doctor studying in America of Peking University, has offered effective decrease to abrade. Assemble and disperse technology ...
Read More »

The development and reform committee of Hubei leads investigating that assist the axle technological transformation project


23rd February 2009 Bearing Technology 0 Comments
Recently, the relevant leading comrades of development and reform committee in Hubei go to assist the open car bearing Limited Company to investigate enterprise's technological transformation project progress on a special trip, He YiXin, Vice President of company,etc. accompanies and visits investigating subsidiary factory and taper of drive shaft roll in the automatic production line of subsidiary factory of the sub bearing, and reported and assisted axle the progress of technological transformation project and benefit produced in recent years. Leading comrades, development and reform ...
Read More »

How to maintain the bearing of the water pump


23rd February 2009 Bearing Technology 0 Comments
1The water pump coming into operation newly, generally must change lubricating grease oil after operating 100 hours ,Run and change once every 500 hours each time later. 2Adopt the floating bearing that lubricating grease lubricates, after running for 1500 hours, should change lubricating grease, there can't be too much or too little oil quantity with note, because there is too muchly or too little lubricating grease will cause the bearing to generate heat, the fuel quantity is generally known in 1/2- 2/3 of the volume of bearing room. 3For adopting the bearing that the lubricating oil ...
Read More »

Stop pushing bearing technical parameter and design


23rd February 2009 Bearing Technology 0 Comments
1.Basic parameter 1 D ...
Read More »

The bearing state of the electrical machinery monitors and diagnoses the summary with the trouble


23rd February 2009 Bearing Technology 0 Comments
It is that an electric locomotive produces the main part of the traction force to draw the electrical machinery, its working state is good or not, influencing the normal operation of the electric locomotive directly. It was standard rolling bearing that Su made electric locomotive of Model 8G and drew the bearing of the electrical machinery and adopted, because it is of low quality that foreign matter is entered, been glossy and bad, installed, year factors such as assaulting and long term administration,etc., may all cause the rolling bearing to appear the abrasion, compression, veneer, ...
Read More »

Ceramic bearing: Internationally acknowledged future main product


19th February 2009 Bearing Technology 0 Comments
On high speed, high temperature, large temperature difference, low temperature, vacuum, require insulatingly, not lead abominable working environment such as the magnetism, the ceramic bearing of high performance is the ideal bearing which substitutes the all steel bearing used at present, range of adapting to the rotational speed is wide, operate and generate heat small at a high speed, performance is steady, longe-lived and able to bear corroding, not afraid pollution, resisting and abrades, is able to bear lacking the lubricated ability of oil the strong and excellent index of performance ...
Read More »